Ihr Warenkorb
keine Produkte

HKS Hipermax S-style C - Toyota PRIUS PHV ZVW35 01/2012-01/2017 - 80110-AT207

Art.Nr.:
80110-AT207
Lieferzeit:
Sonderbestellung Sonderbestellung (Ausland abweichend)
    1.459,00 EUR
    inkl. 20% MwSt. zzgl. Versand

    Rear: Separate type. Recommended rear height: -55mm from stock.
     
    PRIUS PHV ZVW35  
    S-style C 2018 Code No. 80110-AT207
     
     
     

    ▲The above photo is an item for ZVW30.

    Masterpiece of HKS "S-style" series! For the Best & Firm Ride!!

     
    Application   Specification
    Engine 2ZR-FXE(2ZR-3JM)
    Model Year 12/01 - 17/01
    Remarks Rear: Separate type. Recommended rear height: -55mm from stock.
     
      FRONT REAR
    Damping force adjustment - -
    Base valve - -
    Height adjustable lower bracket
    Upper mount Rubber Stock
    Inverted/Normal type Inverted Normal
    Damper/Spring layout Coilover Separated
    Spring rate change at factory Possible Impossible
    Damping force adjustment with wire - -
    Helper spring
    (Spring rate N/mm)
    - -
     
    Ride Height mm
      Factory *2 Test data Adjustable range
    High - Low *3
    Drivable range
    High - Low *4
    FRONT Ride height *1 641 678 ~ 621 678 ~ 621
    Against stock -37 0 ~ -57 0 ~ -57
    REAR Ride height *1 626 638 654 ~ 593 654 ~ 593
    Against stock -67 -55 -39 ~ -100 -39 ~ -100
    *1. Height from road surface to fender arch.
    *2. Height at factory is the data tested at HKS with the setting of Full Kit. (HKS' recommended setting.)
    *3. Adjustable range (However, the lowest value may not be road legal.
    Even within the adjustable range, car body, arm etc. may contact. In such case, it will be hard to drive.
    Damper oil leakage or any other problems caused by low ride height setting from the factory setting will void the warranty of the product.)
    *4. Drivable range that there is no contact of car body or arms etc. (However, change of tire/wheel size may cause a problem.)
    Caution). Actual data depends on each vehicle.
     
    Kit information
    Spring of Full Kit
      F R
    Spring rate N/mm(kgf/mm) 39 ( 4 ) 31 ( 3.2 )
    Free height (mm) 250 -
    Spring type Straight Barrel type Special shape
    Recommended range to change spring rate N/mm(kgf/mm) ±10 -
    Specification of damper
      F R
    Damping force (Rebound/Damping)N* 294 / 108 182 / 118
    Default position of dial - -
    Remaining damper stroke (Rebound/Damping)mm 67 / 60 80 / 90
    * The value of the damping force is at piston speed of 0.1m/sec.
    Setting data
      F R
    Default Test Drivable limit
    High *
    Drivable limit
    Low *
    Default Test Drivable limit
    High *
    Drivable limit
    Low *
    Length of
    case (mm)
    290 327 275 360 378 337
    Spring
    Set length(mm)
    225 225 230 - - - -
    Length to ride hight
    adjuster (mm)
    20 57 0 50 60 74 22
    Lever ratio 1.00 1.20(spg) , 0.92(dmp)
    * Refer to the above explanation *3 of ride height information for drivable high and low limitations.
     
    Test vehicle information
      F R
    Vehicle weight kg 853 583
    Tire size (Air pressure) kPa 215 / 45 - 17 ( 250 ) 215 / 45 - 17 ( 230 )
    Wheel size 7 JJ × 17 off 43 7 JJ × 17 off 43
    Alignment
    (Toe/Camber)
    Test data in 0 mm / -1°36' in 5 mm / -1°36'
    Standard value in 2 ± 2 mm / -0°15' ± 45' in 2 ± 3 mm / -1°30' ± 30'
    * Test data at HKS.
     
    Parts List * It may be changed without prior notice.

     
    Point
     
    ・High ride quality is focused on while floating feeling generated by the stock setting.
    ・C-Wagon provided briskly driving feeling during driving a winding road, but this suspension focus on the ride quality by reducing the front spring rate.
    ・Do not shorten the front case length less than the lower limit since excessive tension is applied to the ABS harness at full bump or steering resulting in the damage to the harness.
    ・Do not extend the front case length more than the upper limit since the stabilizer may come in contact with the lower arm.
     
    ●Required Modification
    The factory rear dust boots must be cut and modified in order to install this product.